Using Apple’s new Lightning to USB3 Camera Adapter

Post Reply
AndyL
New Member
Posts: 13
Joined: Thu Feb 25, 2016 12:21 am
Contact:

Using Apple’s new Lightning to USB3 Camera Adapter

Post by AndyL » Thu Apr 07, 2016 10:20 pm

I noted in a previous post, viewtopic.php?f=183&t=95419 , that Apple have released a new adapter that allows the iPad to be charged at the same time as it is used for transferring data. I have now been using this adapter with an iPad and the Steinberg UR22mkII audio / midi interface.

One side of the adapter was connected to the lightning port on an iPad (4th generation). On the other side of the adapter, with both lightning and USB ports, the connections were as follows. To the lightning port was connected either (i) a battery pack (Anker PowerCore+ 20100 USB-C) or (ii) an Apple 12W USB Power Adapter. To the USB port was connected the UR22mkII (using the USB2.0 port on the Steinberg interface). The power source selector on the UR22mkII was set to the USB 2.0 side. A keyboard was connected to the UR22mkII via a midi cable, and output was monitored on headphones from the UR22mkII.

In operation, the single power source powers both the iPad and the UR22mkII. However, I found while using Cubasis that the iPad failed to charge up: the charge remained constant over about 20 minutes. It appears that in this mode the combined power demands of the iPad and the UR22mkII approximately equal the 12 W of the power supply. However, if a second power supply is used and connected to the UR22mkII USB-C input (and the power switch set to that side) the iPad will then charge up.

Overall, use of the new Lightning to USB 3 camera adapter allows Cubasis to be used on an iPad, connected to an audio interface, without the risk of the iPad running out of charge.

User avatar
LSlowak
Steinberg Employee
Posts: 3077
Joined: Thu Aug 08, 2013 12:36 pm
Contact:

Re: Using Apple’s new Lightning to USB3 Camera Adapter

Post by LSlowak » Fri Apr 08, 2016 9:37 am

Thanks for sharing your experience with the forum community, AndyL!

Best,
Lars
Lars Slowak - Project Management & Team lead Cubasis
Steinberg Media Technologies GmbH
Hamburg, Germany
Check out Steinberg on YouTube, Twitter and Facebook

hornigb
New Member
Posts: 5
Joined: Tue Jan 08, 2019 6:28 pm
Contact:

Re: Using Apple’s new Lightning to USB3 Camera Adapter

Post by hornigb » Thu Jan 10, 2019 5:26 pm

I have some trouble with this configuration. ipad 9.7 2018 with the new camera adapter and i tried everything (update to 1.0.4 firmware for ur22mk2) with 5v dc mode and with usb2 too...It wont work only just for a little time with swithcing to usb2 and with apple battery charger connected to the new camera kit adapter. After i started to play something then it stops to charge my ipad and the usb light goes off. I found a video where are almost the same configuration except ur12 not ur22. The guy have to buy a new noname camera adapter to connect correctly the interface with his ipad...So any idea? Should i buy a new camera adapter?
Here is the video:
https://www.youtube.com/watch?v=FPIPkJka1SI

User avatar
LSlowak
Steinberg Employee
Posts: 3077
Joined: Thu Aug 08, 2013 12:36 pm
Contact:

Re: Using Apple’s new Lightning to USB3 Camera Adapter

Post by LSlowak » Tue Jan 15, 2019 1:56 pm

Hi hornigb,

Thanks for your message.

We recommend to use Apple's original camera adapter when using the UR series audio interfaces with the iPad.

Maybe the adapter you have in use is broken?

Best,
Lars
Lars Slowak - Project Management & Team lead Cubasis
Steinberg Media Technologies GmbH
Hamburg, Germany
Check out Steinberg on YouTube, Twitter and Facebook

Post Reply

Return to “Cubasis | Cubasis 2”

Who is online

Users browsing this forum: No registered users and 2 guests